slednutz tech lounge
 

Go Back   SledNutZ > On the Snow... > Snowmobile How-To's
Ibreakstuff Says: Time to start the snow dance!
Register FAQSled Chat Members List Casino Media Garage Search Today's Posts Mark Forums Read Statistics

SledNutZ Quick Info
Friends of SledNutZ: JohnDee
GreenHulk.net PWC forums
Great Lakes Jeep Thing
Team Belly Pan Sled Forums
PEPPERMILL RENTALS IN THE YOOP! There's no where better to stay in the Rockland/Mass area!
Web hosting by Floogy

sync carbs.

Snowmobile How-To's

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old 12-16-2008
Madcow's Avatar
Madcow
1050 one lunger
Madcow's Info
 
Join Date: Sep 2007
Location: pine city mn.
Posts: 5,057
Default sync carbs.

I use this method as a quick sync, no special tools required and works just fine for trail sleds. plus you dont have the sled running during any of the adjustments smoking up the garage.

with a warm engine adjust idle screws to get the idle where you want it. shut engine down and remove air box. find a drill bit that just fits between the slide and carb body without touching the throttle. since all 3 will be a little different you will find a drill bit that is about average of the 3, the use that to set all 3 idles to the same spot.

now with a 10 mm wrench loosen the lock nut on top of the carbs where the throttle cable screws into the cap. with the throttle held wide open or zip tied wide open make sure that the bottom of the slide goes high enough to clear the opening of the carb. do that on all cylinders.

release the throttle, i stand on the right side of the machine(left and right as you sit on the machine), so on the machines right side facing the seat, with my left hand i control the throttle lever, with my right index finger touching the slide and my pinky touching the slide of the pto carb i slowly sqweeze the gas, what i am feeling for is that both carbs move at the same time. but, the center carb is the one i leave alone, so if the pto carb is opening before the center carb screw the adjusting bolt on the cap into the cap a little.
with them two in sync, I then move my pinky to the center carb and index finger to the mag side carb and do it over again, if the mag side is opening later than the other two you screw the bolt out of the cap until its synced,


once they are all synced, then check the amount of play at the throttle. like brian said you can use a credit card and slip in between the lever and block, then tighten bolts in the cap until the slide just starts to move.

double check that the carbs are in sync, turn the steering hard left and hard right to make sure that the slides dont move up at all. put the air box back on. start the sled, turn the steering again making sure the sled doesnt rev up when you steer, double check idle speed and you are good to go.
__________________
If the boner police are here I need a lawyer.

in a time of deciet telling the truth is a revolutionary act. george orwell.

aint no body ripin like me. M to the a-d-c-o-w. rock it hard for my fly ladies. I rock it yes in deed. homies still roll with me. money dont change me


nothing goes like 3 holes.

BRTECH HOODS
high performance engineering
aaen performance
millennium technologies
Reply With Quote
 


Currently Active Users Viewing This Thread: 5 (0 members and 5 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 07:03 PM.


Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright 2007 Slednutz.com